HausTools keeps its project-wide options on one page:
Edit → Project Settings → Plugins → HausTools. The sections below follow its
groups from top to bottom.
Some are starting values, such as the pitch of a new roof, and leave what you
already placed alone. Others shape every building, such as the roof bevel, and
reach each one on its next rebuild. HausTools.Rebuild in the
console forces one.
The defaults suit a residential building. Grid Unit is the one setting to
check, since it has to match your pack.
A catalog door or window takes its size from its frame mesh. See
Windows & Doors. With no tile picked, the
Openings tool places a plain doorway with no frame, and its size comes from
here.
Setting
Default
What it does
Default Door Width / Height
140 / 230 cm
The size of a doorway placed with no tile picked
Attachment Merge Gap
10 cm
Two adaptive attachments this close merge into one piece. Raise it if flanking pillars that should join stay apart
Gable Opening Snap Distance
25 cm
An opening in a gable snaps to the gable's centre line or a tile seam within this distance. Lower it for freer placement
How close the cursor must be to a wall to pick it, as a fraction of a grid cell. Raise it if walls are hard to click. Lower it if you pick the wrong one in tight layouts
The step the apex arrow snaps the ridge height to while you re-pitch a roof
Roof Centre Snap Distance
30 cm
While you resize a roof, its ridge snaps to a centre line within this distance
Fascia Depth
25 cm
The height of the procedural fascia board. A style with its own fascia piece uses that instead, trimmed by its Fascia Cut
Roof Bevel Subdivisions
1
Cuts across each bevel. 1 gives a single chamfer and more give a rounder edge
These apply only to a roof with no roof style. A pack with a roof style,
BasePack included, sets each of them in the
style's settings instead, and a new roof
always takes that style.
Setting
Default
What it does
Default Roof Thickness
20 cm
The thickness of the roof, measured square to its slope
Roof Wall Clearance
12 cm
How far a roof reaches past the outside face of its walls. It has to cover the cladding and corner posts, or daylight shows at the eave
Soffit Panel Thickness
1.5 cm
The thickness of the soffit panel under the overhang
Roof Bevel
On
Rounds off the roof's hard edges: ridges, eaves and corners
Roof Bevel Width
3 cm
How far the bevel reaches in from each edge
Roof Bevel Hard Angle
30°
An edge gets bevelled when its faces turn by more than this angle
Roof Bevel Weighted Normals
On
Smooths the shading across a bevel, so a narrow one doesn't darken the large face beside it
Appearance is the one look every staircase shares, since none is stored per
staircase. Its railing is plain boxes that a fence style's pack pieces replace.
A fence without pack pieces is built from the same sizes and bevels. See
Stairs.
Setting
Default
What it does
Default Stair Width
100 cm
The width of a new staircase, rounded to whole grid cells
Appearance
Opens into the fields below
Inside Appearance:
Setting
Default
What it does
Handrail Height
90 cm
Height of the handrail above the front edge of the steps
Handrail Width / Thickness
6 / 5 cm
The handrail's width and its top-to-bottom thickness
Newel Size
12 cm
The width of a post
Newel Height
115 cm
The height of a fence post. A staircase's post stops just above its handrail
Baluster Size
4 cm
The width of a baluster
Stringer Thickness
5 cm
The thickness of the side boards, and of the plain lining of a stairwell
Stringer Rise
10 cm
How far a closed stringer stands above the steps, or an open one hangs below them
Handrail, Newel, Baluster, Stringer and Steps Bevel
One set of bevel and grain options per part, below
Steps Bevel covers the treads, risers and landings. Stringer Bevel also
covers the walls under a staircase. Each bevel holds:
Setting
Default
What it does
Bevel
On for Steps Bevel, off for the rest
Rounds off the part's free edges. Where a step sits against another step or a stringer the edge stays sharp
Width
2 cm
How far the bevel reaches in from each edge
Segments
1
Cuts across the bevel. 1 gives a single chamfer and more give a rounder edge
Weighted Normals
On
Smooths the shading across the bevel. Off keeps crisp edges
Rotate Grain
Off
Turns the part's wood grain 90°, for boards whose grain runs the wrong way. It works with the bevel off too, and it leaves fences alone
The pack HausTools opens with. Picking a pack in the catalog's PACK dropdown changes it too. Left empty, it fills in with the first pack HausTools finds. See Compatible Packs