Wall Cladding¶
A wall style covers your walls in meshes from the pack. Pick Clad () and choose Walls on its bar to see the style's pieces.
Shot with the Residential Houses – Modular Pack. See Compatible Packs.
| Section | Tiles | What it is | How to model it |
|---|---|---|---|
| WALLS | 1m, 2m, 3m | Straight wall pieces. HausTools fills each run from the lengths you give it | One, two or three cells long |
| CORNERS | Exterior 90°, Interior 90° | The outside and inside of a 90° turn | To the wall thickness |
| CORNERS | Exterior 45°, Interior 45° | The outside and inside of a 45° turn | To the wall thickness, mirror-symmetric with both arms the same, so one piece fits both ends of a chamfer |
| RUN ENDS | Run start, Run end | Optional caps that close the style's runs. See Run ends | Like a wall piece starting where the run ends |
| FOUNDATION | 1m, 2m, 3m and the four corners | The base course under the ground floor's walls | From the ground to the foundation top |
| STAIRCASE | Wall | One panel for the walls of a stairwell, from the lower floor up to the upper storey's ceiling. It also carries the trim runs | A panel that tiles side to side and top to bottom. It is cut to fit, so any size works, but 3 m wide means fewer seams |
You do not need all three wall lengths. With a 1m piece every run fills. Without one, a run the longer pieces cannot fill exactly keeps an unclad cell, and the Output Log warns you.
Fill an exterior corner for every turn your walls take, because an empty one leaves a gap at the bend. Where a style has no interior corner for a bend, its wall pieces run on to the wall line and cross inside the wall instead, so a lining style can do without inner corners and still fit walls of any thickness. A foundation corner is placed only when its wall corner is filled too. Without one the plain foundation band shows at that corner. Model each piece to the Mesh Rules, with one height across the style.
If a piece faces the wrong way, open its Edit () settings and press Flip facing (), or turn it with Rotation. See Editing a piece.
Run ends¶
RUN ENDS holds two optional caps, Run start and Run end. HausTools places one wherever a run of the style stops against another style, an unclad face or a free wall end, so a band, a cornice or a canopy no longer shows its open end where the cladding changes. Where the face carries on in the same style, along the wall or round a corner, no cap is placed. A run that wraps a corner and stops just past it gets its cap at the end of the corner piece's arm.
Model a cap like a wall piece that starts where the run ends, with the run behind it. To seat it, choose Edit () from the cap tile's actions menu. Its Transform card has Pivot X / Y / Z and Rotation, measured from the run's end: X along the run, Y through the wall and Z up. Removing a cap clears its seating too.
A cap is not yet placed at a corner where a corner piece stands.
Staircase trim runs¶
Trim runs are profiles such as a skirting board, a cornice or a dado rail, tiled along a line of the stairwell walls. Open the staircase Wall piece's Edit () settings and add them with the Trim tile under TRIM RUNS. A style can carry any number.
| Setting | What it does |
|---|---|
| Line | The line the run follows: Bottom is the lower floor, Top the upper storey's ceiling and Custom a height you set |
| Line height | How far above the lower floor a Custom line sits, in centimetres |
| Pivot X / Y / Z | Moves the profile off its line, in centimetres |
| Rotation | Turns the profile about its vertical axis, in degrees |
| Upper floor | What the run does on the storey above. See below |
Flip facing () turns the profile around.
Upper floor carries a Bottom or Custom run up the stairwell. A Top run ignores it.
| Value | What the run does |
|---|---|
| None | Stays on the lower storey |
| Fill Gap | Also fills from the top step to the nearest grid line on the landing floor |
| Whole Run | Repeats along the whole stairwell wall upstairs |
| Follow Stairs | Fills the gap, rakes down beside the flight and carries on under it, cut along the stringer |
📷 Screenshot: a stairwell with skirting set to Follow Stairs, raking down the flight.