Skip to content

Fences & Railings

The Fence tool draws railing runs: a porch balustrade, a balcony rail, or the guard around a stairwell. It also draws panel fences for gardens and boundary walls, built from whole panels. Fences are drawn run by run on the grid, like walls, and take their look from a fence style.

Shot with the Residential Houses – Modular Pack. See Compatible Packs.

Drawing a fence

  1. Select the Fence tool (), in the toolbar's Building tools group.
  2. Click to anchor one end of a run, or hold and drag toward the far end.
  3. Click again to build that run, or release the drag.
  4. Repeat for the next run. Esc cancels a run in progress; with nothing pending it hands you back the Edit tool.

Start a new run where the last one ended and the two become one fence. Carry on that way round a deck and the whole balustrade is a single piece: click any part of it with the Edit tool () and move or delete takes all of it.

A selected fence carries an arrow on each of its runs. Drag one and that run slides to either side in whole grid cells, exactly as a room is reshaped by the arrow on one of its walls. The fence stays in one piece behind it.

Snap dots mark the corners of every fence on this storey, and the one your run will land on glows green.

Faster than run by run

Shift + drag draws a closed rectangle of fence in one gesture, Ctrl + drag deletes the sections along the drag, and Ctrl + click, click deletes the span between the two clicks.

What a fence is made of

A fence has three elements, and a fence style decides how each looks:

Element What it is
Rail The swept top handrail that follows the run
Post A post at each vertex, either a decorative newel or a structural support
Baluster The spindles between the rails

The shapes come with the pack, and a fence drawn without a style still builds in a plain default form. The style card sets the run's height, the baluster gap and how high the balusters sit. Bottom Rail adds a second rail under the top one, and Posts Only drops both for an open covered porch.

Structural posts

Structural Column turns a run's posts into the columns that carry a porch roof. Every corner of the fence becomes one. Nothing changes without a roof overhead, so the tick on its own leaves rail-height newels standing.

A column is the one fence element whose height the pack does not choose. Its mesh is authored at a nominal height and stretched upward to meet the eave. An empty Column slot falls back to a procedural box.

A railing along a deck edge opens a gap at the landing of porch steps. The rail, the balusters and any post in the span go, but a column stays. Move or delete the steps and the fence closes again by itself.

Panel fences

A fence style can be built from whole panels instead of a railing: a garden fence, a picket fence or a low boundary wall. Panel styles are drawn exactly like any other fence. HausTools lays the style's panels along each run like wall cladding, the longest that fit first, and stands the style's Pole at every open end. With Pole at Every Joint on, a pole also stands between every two panels, like a brick wall's pillars. It is a setting on the fence style, at the right of its tiles in the catalog (see Style settings).

A wooden panel fence, then a brick wall with Pole at Every Joint on.

Panels can come with random variations, so a long run does not repeat the same panel over and over. Which panels a style has, and its variations, are set up in the pack. See Fences, Decks & Stairs.

A panel fence has a front and a back. Press F in the Fence tool to turn the panels of the next fence to the other side, or select a fence with the Edit tool and press Flip () on its Edit widget.

Painting

Select the Material tool () and click a part of a fence. The rail, the posts and the balusters each take their own swatch. Shift + click paints every piece of that kind along the run and on any fence connected to it. See Placed pack pieces.

Hotkeys

Input Action
Click Anchor one end of a run, then click again to build it
Drag Draw one run in a single gesture
Esc Cancel the run in progress; otherwise back to the Edit tool
F Turn a panel fence's panels to face the other side
Shift + drag Draw a closed rectangle of fence in one gesture
Ctrl + drag Delete every fence section along the drag
Ctrl + click, click Delete the span between the two clicks
Del Delete the selected fence

Full list: Hotkeys.

Guarding a stairwell

This is where fences do the most work. Draw a guard rail around a stairwell hole and:

  • It snaps onto the opening's rim, not the grid line beside it, so the balustrade stands flush on the hole even though the hole hugs a wall-fitted stair. The points you draw stay on the grid.
  • It opens a walk-through gap where the staircase arrives on the floor above, its edge posts landing on the line of the stair's own railings.
  • It owns the stair's top posts, so the staircase stops planting its own and its handrail runs on up the rake to die into the fence post, the way a porch rail does. A fence standing across the stair short of its exit pulls that handrail back to terminate inside the post.
  • It follows a hole resize: pushing a face arrow carries the fence corners on the moved rim with it, in one undo step with the hole.