Skip to content

Platforms & Decks

A platform is a raised rectangle of ground: a deck, a terrace, a porch floor, or the foundation the building stands on.

Drawing a platform

  1. Select the Platform tool (), in the toolbar's Building tools group.
  2. Drag a rectangle. The size reads out as you drag.
  3. Release to place it.

Drag a second rectangle against the first and the two become one deck. Any deck the new rectangle overlaps or touches is fused in, and the result is re-traced as a single outline, which is how an L or U shaped porch is built. The deck that was already there keeps its style, so the new area takes on its look and its height. Moving a deck into another joins them the same way.

A rectangle dragged against the deck already on the front: the two fuse into one deck around the corner.

Select a deck with the Edit tool () and every edge of its outline carries an arrow to push or pull, just as a room is reshaped by the arrow on one of its walls. Alongside them is a two-button menu: move and delete.

Deck height is a property of the style, not of one deck. It is the Deck Height slider on the platform style card in the catalog: 0 to 300 cm, 100 cm out of the box, and every deck wearing that style stands at it. An unclad deck sits at 100 cm. The slab sits at that height above the ground, and the skirt fills the gap up to it.

Because the height rides the style, giving a porch and a low terrace different heights means giving them different styles.

A platform against the building raises it

Put a platform on or against a room and the building rises to meet it. Every wall in that connected structure takes a foundation up to the deck's top, so the floor comes level with the deck and the walls, floor and roof all move together. This works from either direction, drawing a platform against a room, or moving, edge-dragging or extruding a room into a platform.

The raise is one-way. While a deck supports the room, the Edit tool's foundation-height arrow will not travel below the deck's own height. Delete the deck and the building stays where it is: the arrow can then bring it back down, but nothing lowers it for you.

To put one room's floor back down at ground level, a garage for example, use the room's floor-drop button instead. See Floors & Ceilings.

Porches

Bring a roof out over a raised deck and you get a porch. Instead of leaving the roof's underside bare, HausTools finishes it: a soffit ceiling closes the underside above the deck, and siding fills the gable above it. The eaves' fascia band carries on around the low sides, with header beams boarding the rest on that same line.

The finish does not stop at the deck edge. Where the same roof reaches past it over open ground, the underside is closed the same way, so the porch ceiling runs unbroken out to the eaves. See Roofs → Porches.

A porch is dressed from the roof style, not the deck's. The ceiling takes that style's Soffit piece and the band around it takes the Fascia.

Shot with the Residential Houses – Modular Pack. See Compatible Packs.

Stairs connect to decks too: a staircase placed in front of one shortens to land flush on its edge. See Stairs → Porch steps.

Railings

Rail a deck with the Fence tool (). A fence along the edge opens a walk-through gap where a connected stair lands, and its style decides the rest: Structural Column replaces the run's posts with the pack's column piece, and Posts Only drops the rail and balusters for an open covered porch. See Fences & Railings.

Cladding a Platform

A Platform style sets the height and the cladding: skirt tiles along every exposed side, and a corner piece wherever the outline turns.

There are two ways to arm one. Pick the Clad tool () and choose Platform on the bar that drops in under the toolbar, or simply switch to the Platform tool (), which arms that class's active style for you, so cladding a fresh platform needs no extra style click. See Cladding.

The Clad tool, then Platform on the type bar: the catalog switches to Platform styles, and a click skirts the deck.

Colour is separate from cladding: the slab and the skirt take their own materials, and a clad skirt paints piece by piece. See Materials & Painting.

Hotkeys

Input Action
Del Delete the selected platform
Esc Cancel a move in progress; otherwise deselect

Full list: Hotkeys.