Skip to content

Stairs

You place a staircase by its foot and the direction it climbs, and HausTools generates the rest: how many steps the climb takes, the stringers, the rails, and the stairwell hole it cuts through the floor above.

Placing a staircase

  1. Select the Stairs tool (), in the toolbar's Building tools group.
  2. Move the cursor to where the bottom step goes. A ghost of the real staircase follows, with treads, risers and side boards at the step count you'll actually get.
  3. Aim it: drag from the foot in the direction it should climb, or press , / . to turn the pending stair 90°.
  4. Click to place it.

The stair always climbs exactly one storey. The step count comes from that climb and a target riser of 18 cm, with treads 28 cm deep to start; both can be overridden per stair once it is placed. Green start and end handles mark where you enter at the bottom and step off at the top.

The foot, the aim, the click. The stairwell upstairs comes with it.

If the top lands near a wall, the tread depth auto-fits so the exit edge seats exactly on the wall face. The correction spreads invisibly across every step and the foot stays where you put it.

Editing a placed staircase

Select it with the Edit tool (). You get handles in the viewport and its Edit widget beside it.

Handles

Handle What it does
Two side arrows Widen or narrow the stair, a grid cell at a time
One end arrow Change the run length on a straight stair: the treads stretch or squeeze, shallower or steeper, at the same step count
Wing handles One per flight. Drag left or right to turn that flight, making an L or a U
Landing handles Appear once a wing handle has made a turn. Drag one to slide its landing up or down the climb, changing how many steps fall above and below it

The end arrow is for straight stairs. Once a stair has turns, you reshape it with the wing handles instead.

The square and arrow at the foot are the placement markers, not handles.

Edit widget

Icon Action What it does
Rotate left Quarter-turn the staircase anticlockwise
Move The stair follows the cursor; click to place it
Rotate right Quarter-turn the staircase clockwise
Railing A balustrade along the edge of the flight, newel posts, balusters and handrail: None · Left · Right · Double
Stringer boards The side boards carrying the steps, one down each edge of the flight. Closed hides the step ends behind a clean diagonal, Open notches the treads in with their ends exposed, None has no board at all
Under-stair walls A wall under the flight on the chosen side, from the floor up to the stringer, so the space under the stairs is boxed in: None · Left · Right · Double
Step count A Steps field forcing the count, typed, stepped with its arrows or dragged; Auto beneath it hands the count back to the climb
Delete Remove the staircase

Left and Right in the Railing and Under-stair walls pickers are from the point of view of someone walking up the stairs.

The three Stringer boards options on the same staircase.

Hotkeys

Input Action
, / . Quarter-turn the staircase: the pending one before you click to place it, a selected one in place, or a Move ghost while it follows the cursor
Del Delete the selected staircase
Esc Cancel the placement or the move in progress; otherwise deselect

Full list: Hotkeys.

Turning a staircase

Drag the wing handle at the foot sideways and the flight above it turns, giving you a landing and an L. Every flight then carries its own handle: steer a turn left or right, or drag the bottom one again to add another turn below. Two turns the same way make a U, two opposite ways a switchback, and further turns carry on round into a spiral. Dragging the bottom turn back to centre removes it.

Each turn remembers which side it goes to and how many steps sit above it, so you can slide a landing up or down the climb without redrawing anything.

A flight flank or landing edge that meets an interior wall is pulled in to that wall's face, so a turned staircase fits the gap it actually has rather than clipping through. The rail, the stringers and the walls under the stairs ride the same fit.

The wing handle dragged sideways: the straight flight folds into an L with a landing.

Stairwell

Every staircase cuts a hole through the floor above it, so the climb comes out on the next storey. The hole covers the whole flight and sits on the grid lines, except at the top step, where it ends flush. Each open edge is finished so the raw cut never shows. A fence style can carry a stairwell Fascia. If the pack has one, that board runs along the edge. Without it HausTools lines the opening through the full depth of the floor. Edges against a wall are skipped because the wall already closes them.

To resize it, go up to the storey the staircase arrives on with Floor up () on the floor stepper. Select the Edit tool () and click the opening. The cut is outlined on that floor with four face arrows that push or pull each side a grid cell at a time. There is no Edit widget for the opening. The change is saved with that staircase and can be undone.

No railing comes with the hole

The stairwell is just a hole. Select the Fence tool () and draw a railing around the opening. It snaps onto the rim and opens a walk-through gap where the staircase arrives. The gap's edges line up with the staircase's own rail lines, so the posts stand centred on them. See Fences & Railings.

Porch steps

Select the Stairs tool () and place a staircase facing a platform deck no more than six grid cells from its edge. It becomes porch steps: the climb stops at the deck's height and the top step lands flush on its edge. The placement ghost shows all of this before you click.

HausTools picks a comfortable number of steps. Set your own with Step count () in the Edit widget. Porch steps can also start on a low deck and climb onto a higher one.

Porch steps differ from other staircases in three ways:

  • The end arrow moves to the foot. Dragging it slides the foot toward or away from the deck and the treads re-fit. It stops before the steps would come off the deck.
  • They cut no stairwell because there is no floor above to cut.
  • They show no wing handles and can't be turned into an L or a U.

A fence along the deck edge opens a gap for the steps, and the fence's own posts take over at the top of their railing.

Cladding a staircase

Three parts of a staircase take pack pieces:

  • The railing is built from fence pieces. Select the Clad tool () and its Fence chip, pick a fence style and click the staircase. See Staircase railings are fences.
  • The shaft walls take the staircase panel and its trims from the cladding style already on them, tiled and cut from the lower floor up to the ceiling above. A wall only gets it when another wall stands on top of it upstairs.
  • The walls under the staircase take the staircase panel and its trims. Select the Clad tool and its Walls chip, pick a cladding style and click the staircase. The panel is cut to the slope of each flight. A staircase without under-stair walls gets them on both sides.

A wall face under the cursor takes that click first. Aim where the staircase's white outline shows.

The steps themselves take no pack pieces. Select the Material tool () to colour them instead. See Painting and What you can paint.

Shot with the Residential Houses – Modular Pack. See Compatible Packs.

Building your own pack? The panel and its trims are set up in Staircase trim runs.

Painting

Select the Material tool () and click a part of a staircase. Treads, risers, landings, side boards, the railing and the walls under the staircase each paint on their own. One click on a tread repaints every tread on that staircase. The side boards and the plain lining of the stairwell paint together.

Clad walls under the staircase paint piece by piece instead. The panel and each of its trims take their own paint, one material at a time. The staircase panel on a shaft wall wears that wall's paint.

A railing with a fence style takes paint like any placed piece. A click paints only the material under the cursor on that piece. Shift + click paints it on every piece of that kind on the staircase, such as every post or every baluster.

Defaults

The Stairs group in Project Settings → Plugins → HausTools sets the width a new staircase is placed at. It also holds the look of the handrail, newel posts, balusters, side boards and bevels. None of that is stored per staircase, so change it and every staircase follows on the next rebuild. A railing with a fence style takes its look from the style instead. See Project Settings.