Skip to content

Rooms

The Room tool () draws four mitred walls in one drag, the fastest way to block out a plan. Once drawn, a room is also a thing you can select: move, rotate or copy, add a storey, or drop its floor.

Drawing a room

  1. Select the Room tool (), in the toolbar's Building tools group.
  2. Drag a rectangle. The size reads out in metres as you drag.
  3. Release. You get four walls, already mitred at the corners, and, because the loop is closed, a floor. A ceiling follows only once a storey sits above the room.

The Walls tool can do this too

Hold Shift while dragging with the Walls tool () and it draws a room instead of a run. See Walls → Drawing.

Selecting a room

Click inside it with the Edit tool (). Its Edit widget has nine buttons:

Icon Action What it does
Rotate left Rotate the room a quarter turn anticlockwise
Move The room follows the cursor as a ghost; , / . rotate it while it moves; click to drop. Move and rotation commit as one undo step
Rotate right Rotate the room a quarter turn clockwise
Copy Duplicate the room
Floor Add a storey to this structure, the same action as the toolbar's add-floor button
Delete Remove the room
Hide Build the room empty, with no floor, ceiling or inside walls. Click again to show it. See Hiding a room
Drop Toggle the room's floor down to ground level. Greyed out until the room stands on a foundation, and only on the ground storey. See Floors & Ceilings
Ceiling Height Override Give this room its own ceiling height. See Ceiling height

Raising a room onto a foundation

Select a whole room and an up arrow appears at its floor level. Pull it and the room rises onto a foundation, snapping in 25 cm steps to a maximum of 1 m. The cap is there because a pack's foundation pieces are authored a metre tall. Both figures are in Project Settings.

Height is not held per room. It is shared across everything the walls connect to, so a connected floor is always level: lift one room and the rooms joined to it come up with it.

Pulling one room's up arrow lifts every room its walls connect to, so the floor stays level.

Two limits:

  • Ground storey only. The arrow is absent on an upper storey, where the lift is not a property of that storey at all. It lives on the ground.
  • A deck sets the lower bound. Where a platform covers or abuts the room, the arrow will not travel below the deck's own height.

A platform raises it too

A room can also be raised without the arrow. Move or resize it into contact with a platform and it lifts onto that foundation, exactly as drawing a platform against the room does. See Platforms & Decks.

Reshaping

Select one of a room's walls and a single arrow appears, pointing out of that wall. Pull it and the wall moves outward or inward, taking the walls either side with it so the loop stays closed, resizing the room without redrawing it.

The arrow snaps in whole grid cells, so a reshaped room stays on the grid and keeps mitring cleanly.

Openings, cladding and everything else attached ride the wall they are on. The preview ghost is massing only, so a door will not appear in it while you drag, but it is still there when you let go.

Pulling one wall's arrow moves it in whole cells; the walls either side follow, so the room stays closed.

It works on a lone wall too

Select a wall run that no room encloses, pull its arrow either way, and HausTools adds the three walls that close the rectangle behind it, turning the run into a room. See Walls.

Hiding a room

Hide () is on the bottom row of the room's Edit widget. Click it and the room is built empty: no floor, no ceiling and no wall pieces on the walls inside it. Use it for an unfinished room, or one you will only ever see from outside.

Everything around the room stays: its outside walls, the room next door, the floor of the storey above and the roof. A hidden ground-floor room keeps its foundation. The eye stays highlighted while the room is hidden, and a second click shows the room exactly as it was.

The room stays hidden when you move, turn, copy, resize or merge it.

Ceiling height

A room's ceiling normally sits at the Ceiling Height of the wall style lining it (see Making a Style). Ceiling Height Override (), the gear at the bottom-right of the room's Edit widget, gives one room a height of its own:

  1. Click the gear. A dropdown opens under it.
  2. Untick Pack Default. The Height slider wakes up, starting from the room's current height.
  3. Set the height above the room's floor, in centimetres.

Tick Pack Default again to go back to the wall styles' height. The gear is ringed while the room sets its own. A ceiling never rises above the storey height. The setting moves, turns, copies and is deleted with the room, and a room grown by its edge arrow keeps it.

Clicking inside the dropdown does not close it. A click outside it does.

Hotkeys

Input Action
Ctrl + drag With the Room tool, delete every wall inside the rectangle, ghosted red while you drag
, / . Rotate the selected room, or the move ghost while it follows the cursor, 90°
Del Delete the selected room
Esc Cancel a move in progress; otherwise deselect
Ctrl+Z / Ctrl+Y Undo / redo

Full list: Hotkeys.