Skip to content

Catalog & Placement

The catalog is the library along the bottom of the viewport. Everything you place or paint comes from it: cladding, windows and doors, roof looks, materials and your baked buildings.

It is also where you build your own pack. Packs, styles, pieces, frames and extra meshes are all authored in the viewport, never by editing a data asset.

This page covers the catalog itself. Placing its pieces on a building, painting them and baking the result are covered in Finishing.

How to read it

The catalog is one dock in two halves. The left holds your pieces and the right shows what's in the active style.

  1. PACK, the pack you're working in. Its dropdown switches pack and holds New Pack. Each pack in it has an actions menu with Show in Content Browser, Duplicate, Rename and Delete.
  2. STYLES, the styles in that pack, with a + to add one. A style is one look, such as "Red Brick" or "White Render". Click one to make it active and drag to reorder. Its gear () or a right-click opens its actions menu: Rename, Duplicate and Delete.
  3. The breadcrumb, reading pack › style.
  4. The filter icon (), on wall cladding and openings.
  5. The tiles, in labelled sections.
  6. Rename () and delete () for the active style, and the chevron that collapses the dock.

Wall, roof, fence and platform styles also show their own settings, pinned to the right of the tiles.

Beside the +, the placement debug button () shows or hides an overlay that labels every placed pack piece with its mesh name and every wall run with its length. See Console Commands.

The catalog follows your tool

You never pick a category in the catalog. Choose a tool in the toolbar and the catalog shows the matching content:

Icon Tool The catalog shows
Clad the active style's cladding pieces
Walls wall cladding styles
Room wall cladding styles
Openings that style's windows and doors
Roof roof looks
Fence fence styles
Platform deck styles
Material the material palette
Buildings your baked buildings

Going the other way works too: click a tile and HausTools switches to the tool that places it.

Collapsing it

The chevron () at the right end of the header rolls the catalog down to a slim bar and gives the viewport its height back. The bar keeps showing pack › style, and its chevron () brings the catalog back up.

Filter

On wall cladding and openings, the filter icon () opens a list of tick boxes that narrows which tiles show:

Showing Tick boxes
Wall cladding Walls, Foundation, Staircase
Windows and doors Windows, Doors

Untick Foundation to browse wall cladding alone, or Doors to see only windows. Corner pieces count as Walls. A highlighted icon means some tiles are hidden.

A pack can give windows and doors a category of its own, such as Storefronts, Shutters or Exterior Doors. Each category is its own gallery section after Windows and Doors, with its own tick box in the filter. Pieces with no category stay under Windows or Doors. Categories only organise the catalog: they never change where a piece can go. To set one, see Windows & Doors → Options.

Style settings

Wall, roof, fence and platform styles have settings of their own, to the right of their tiles. They belong to the style, so changing one changes everything built with that style.

Wall styles

A wall style's settings sit at the right of its tiles, under HEIGHTS and THICKNESS. Each group starts on Pack Default, which keeps the pack's own values. Untick it to set the style's own.

Setting Default What it does
Storey Height Pack Default The height of the storeys this style stands on. Where styles on one storey differ, the largest wins. See Storey heights
Ceiling Height Pack Default The ceiling height, from the floor, in rooms lined with this style. A room can override it
Wall Thickness Pack Default The thickness of the walls this style clads. A wall clad on both faces takes the thicker style's. See Walls

Roof styles

Setting Default What it does
Thickness 20 cm The thickness of the roof slab, measured square to its slope
Overhang 30 cm How far the eave projects past the footprint
Fascia Cut 0 cm How much to cut off the fascia board's depth. At 0 the board stays as modelled
Soffit Thickness 3 cm The thickness of the soffit panel under the overhang. Match it to the soffit piece
Wall Clearance 12 cm Extra room at the eave so the roof slope clears the top of the wall and its cladding
Bevel Hard Edges Off Softens the shell's hard edges
Weighted Normals Off Shades the bevel as one surface
Bevel Width 0.8 cm How wide that bevel runs
Bevel Angle 60° An edge is bevelled when its faces turn by more than this angle
Procedural Finish Off For a style with no roof pieces: builds a finished, paintable roof from plain surfaces instead of a rough preview. See Roofs & Gutters

Fence styles

Build Type picks how the fence is made. Railing, the default, sweeps a rail over posts and balusters, for porches, balconies and stair rails. Panels lays whole panels along the run, with the pole closing each open end. See Panel fences.

A railing style has these settings:

Setting Default What it does
Height 100 cm The railing's height
Baluster Gap 12 cm Spacing between balusters
Baluster Lift 0 cm Raises the balusters off the ground
Bottom Rail Off Adds a second rail near the ground
Structural Column Off Lets the posts hold up a porch roof. See Fences & Railings
Posts Only Off Leaves out the rails and balusters

A panel style has these instead:

Setting Default What it does
Pole at Every Joint Off Stands the pole between every two panels as well as at both ends, like a brick wall's pillars. Off, only an open end gets one, for panels that carry their own post
Height 100 cm How tall the fence's collision stands, and the Edit tool's outline

Platform styles

Setting Default What it does
Deck Height 100 cm How high the deck stands, with the skirt filling the gap to the ground

A whole slider drag is one Ctrl+Z step, not one per notch.

Materials palette

With the Material tool (), the catalog becomes the paint palette: your swatch groups on the left and their swatches on the right. See Materials & Painting.

Buildings library

With the Buildings tool (), the catalog lists every building you've baked, one tile each. See Placing copies.

Adding and editing pieces

Click a tile to select it and load that piece for placing or painting. Right-click it, or click its gear (), to open its actions menu: Edit (), Show in Content Browser () and Remove (), plus Duplicate () and Pair with style on a window or door. Double-clicking a tile does the same as Edit. Remove takes the piece out of the style and leaves the mesh in your project.

Each section ends in a + tile named for it, such as Walls or Doors. Click it to pick a static mesh, or drag one in from the Content Browser, and HausTools files it into the right slot by its size. Hover the tile and click its arrow (), Use Selected Assets from Content Browser, to add every mesh selected there at once. Dropping a mesh onto a filled tile replaces that piece.

Edit gives the whole catalog over to that one piece, with its pivot, rotation, frame and extra meshes on cards and a Done button to go back. Every setting is covered in Making a Style.

Keys for a selected tile

Key Does
Enter Edit
Del Remove
F Show in Content Browser
Esc Deselects the tile